How to Make Your Shoes Non Slip with Household Items
Want to know how to make your shoes slip resistant? You’re in the right place as we’ll show you how to make shoes and boots ready for winter. Whether it’s trudging through ice, powdery snow or slippery surface, it’s essential you learn how to make your shoes non slip.
But lets learn how to solve this problem with home materials.
Table of Contents
How to make your shoes non slip at home
Materials You’ll Need
- Traction adhesives
- Grip pads
- Spray pads
- Nail File
- Rubber Glue and Salt
- Dry sand
- Puff paint
- Masking Tape
Scuff the Shoes
If you want to know how to make your shoes non slip, start by scuffing them on rough surfaces. This is most common in new shoes, but soles develop a stronger grip when abrasions and nooks develop. You just need to walk on rocks, gravel and rough concrete. Try this on rough textured walkways and textured metal grates. Anyway, You don’t even have to walk: just rub the shoes over these surfaces and the grip should improve.
Sandpaper the smoothest parts of the shoes. Use a 50 grit sandpaper (anything a bit coarse is okay). This technique may not be that effective on flats and sandals however. Just keep sanding until the surface gets a bit rough.
If sandpaper doesn’t work or you don’t have one available, use a nail file instead. Use this like sandpaper and scuff the flat, smooth sections of the shoe that make contact with the floor. Metal files are the most efficient, but you can use an emery board in a pinch. Just like with sandpaper, the coarser the better.
If your shoes are already worn out, use grip pads. You apply these textured pads on the sole. Buy only quality grip pads so your shoes don’t end up feeling sticky. The good thing is grip pads aren’t expensive and widely available.
Also known as spray-on coating, you can use this in lieu of adhesive pads. There are many types of grip sprays so look for one that’s a good match for your shoes. Traction sprays and grip pads have the same function and are often sold in the stores, though sprays can be more expensive.
Another way of making shoes less slippery is to apply a good amount of hairspray on the soles. Let the hairspray set for a minute before you go out and walk. This isn’t a permanent solution, but it will do in case of an emergency and you don’t have any nonslip solutions nearby.
Look up how can I make my shoes less slippery on the web, and you’ll find puff paint among the methods used. Puff paint refers to a kind of paint used in children’s arts and crafts. After the paint has dried, it develops a textured, rough surface. This is good enough to improve shoe grips. Just apply a thin layer of paint on the sole, let it dry for a few hours and wear them.
Puff paint lasts longer than hairspray, but you do need to re-apply it for optimum results. Like hairspray, this is not a permanent solution.
Masking tape gives you a quick way to increase traction. Just apply a couple of masking tape rolls in an X layout. Apply these on the flattest and widest parts for optimum effects. Masking tape is good, but it’s only going to work as long as there’s adhesive left.
Rubber Glue and Salt
A bit of grainy texture can improve the grip on your shoes so they don’t slide around. Mix salt and glue and apply on the bottom of your shoes. Wait a couple of minutes and then walk around.
This is one of the easiest ways to improve shoe traction is to use sand. Use spray adhesive and apply the sand along the bottom.
If the methods above don’t work or you don’t fancy the DIY approach, just buy ice grips. You put this on your shoes or boots and you’ll be able to walk on snow and ice.
Knowing how to make shoes slip resistant is essential if you spend time outside during winter. Slipping isn’t just embarrassing, as a dangerous fall could lead to injuries. Yes, you could buy nonslip boots and shoes, but they are expensive. By following the tips you’ll be able to walk on slippery surfaces with confidence.